Diverter flashing
A kickout is added where a roof edge ends against a wall which protects the wall below.
Roof Repair
Flashing Repair Montvale, NJ
A Montvale roofer can stop leaks where the roof meets a wall, dormer, skylight or edge by renewing the flashing at that joint, so water is shed by the metal itself. Dial (551) 390-0362 to talk with a local roofer about the flashing.
Flashing is the thin metal that seals every place the roof surface is interrupted. The main types are step flashing at sidewalls, apron flashing at headwalls, counter flashing over the top, kickouts at the bottom of walls, valley metal and drip edge at the edges. When any piece is missing, loose or rusted through, water gets behind the roof covering.
Flashing problems often hide inside the wall rather than on the ceiling. A missing kickout is a classic example: water running down the roof edge pours behind the siding at the bottom of the wall, and the rot shows up later as soft trim, stained siding or a damp window below. By the time it is visible, the repair may include some siding and wall sheathing too.
A bead of sealant along a joint is a warning sign, not a repair. Sealant can hold for a while, but it fails sooner or later, and the joint leaks once more. Lasting flashing repair means new metal installed in the right order, with sealant only as a backup.
Many flashing repair calls in Montvale also turn up a need for chimney flashing repair or roof leak repair.
Looking for Montvale flashing repair? Call (551) 390-0362 to talk to a local roofer.
Call nowThe process
How flashing repair works
Here is how a roofer typically approaches a flashing repair.
Inspect the joint
Each joint is examined for missing kickouts, loose step pieces and counter flashing that no longer covers the top. Damage in the wall changes the scope, so it is checked early.
Expose the old metal
Siding is lifted or removed along the joint so the old flashing and housewrap can be reached. That is the only way to lap new metal behind the wall weather barrier.
Weave in the metal
New step flashing is installed one piece per shingle course, each lapping the one below, with a kickout diverter at the bottom. Nails stay on the horizontal leg, high enough to be covered by the next shingle.
Cover the top
The weather barrier laps over the step flashing, and siding is reinstalled with clearance above the roof surface. Siding pressed tight to the shingles stays wet and rots.
Check drip edge
At the roof edges, drip edge is reset or replaced to protect the fascia and deck edge. The lap order differs at eaves and rakes, and getting it right matters.
What is included
Flashing a roofer can repair
Apron flashing
The flashing across the top of a roof section is redone with proper laps over the shingles.
Counter flashing
Cap flashing on masonry is reset into the mortar joint without relying on caulk alone.
Edge flashing
Drip edge is added where it was left off so water drips clear of the fascia.
Sidewall flashing
Sidewall flashing is rebuilt one course at a time so water stays on the roof.
Related service
Roof Flashing Repair Montvale, NJ
The scope of a flashing repair depends on the joint and on how much damage the water has done. A lifted counter flashing on a masonry wall may only need resetting into the mortar joint, while a leaking sidewall usually means new step flashing, new shingles along the wall and some siding work. Knowing the scope up front avoids surprises once siding comes off.
Material matters too. Copper, galvanized steel and aluminum all show up on roofs, and each has spots where it works best. Mixing copper with aluminum or galvanized metal in contact can cause corrosion, so the roofer matches the metal to what is already there.
Related service
Roof Valley Flashing Montvale, NJ
Roof valleys carry the runoff from two slopes, so they handle more water than any other part of the roof. Valleys are either open, with exposed metal, or closed, with shingles running through them. Either way, a self-adhered membrane should line the valley under everything else.
Common valley problems include rusted metal, debris dams, worn shingles and nails placed too close to the centerline. Small installation details, like clipping the upper corners of the cut shingles, keep water flowing down the valley instead of across it. Valley repair usually means removing the shingles along the valley, replacing the membrane and metal and reshingling with the right cuts.
Local help
Flashing Repair Near Me
In Montvale, many flashing problems date back to an old reroof where the original flashing was reused or caulked instead of replaced. Homes in Montvale and nearby towns like Park Ridge, Woodcliff Lake, Saddle River and Hillsdale range from older houses with aging galvanized flashing and no kickouts to newer homes with complex rooflines that rely on many wall joints, so a close look at every joint is worth asking for.
Need flashing repair around Montvale? Call (551) 390-0362 for a Montvale roofer who serves the towns around it too.
Roofs in this climate
Cold winters bring snow, ice and a long stretch of freezing nights. When warm attic air melts the snow, the meltwater runs down and freezes again at the eaves, building ice dams that push water up under the shingles. Coastal storms and heavy spring rain drive water sideways into flashing, valleys and old chimneys. That is why roof repair in Montvale is busiest after a hard winter and before the next one.
Why call
Why not wait
Less damage
A roof problem fixed early rarely spreads to the decking, the insulation or the ceilings.
Familiar with local homes
Roofers in Montvale know the roof types and weather wear common in local homes.
Clear next steps
Ask your questions before you agree to anything.
Flashing Repair FAQ
Is it possible to fix flashing without a new roof?
Flashing is repaired on existing roofs all the time. The roofer removes the shingles and siding along the joint, installs new flashing and reshingles that strip. If the roof is near the end of its life, it can make sense to replace flashing as part of a reroof instead.
Why does my roof need kickout flashing?
A kickout is a small diverter at the bottom of a roof-to-wall joint, where the roof edge ends against a wall. It turns water that runs down the step flashing outward into the gutter instead of letting it pour behind the siding. Without one, the wall below that joint often rots quietly for years.
What is step flashing and why does it matter?
Step flashing uses individual bent pieces that interleave with each shingle course. The overlap carries water down the wall joint and out onto the shingle surface. A long single strip sends water under the roofing, which is why step pieces are the standard.
Can I just seal the flashing with caulk?
A bead of caulk may hold for a season or two, but it will fail. Over time, it hardens, splits and lets the joint leak again, often worse than before. A proper repair replaces the metal so it sheds water without depending on sealant.
What are the signs of bad roof flashing?
Look for stains or drips that line up with a roof-to-wall joint. Outside, look for rust, gaps, lifted metal, nails through the face and heavy caulk along the joint. Stained trim where a roof edge meets a wall is a common clue too. Call (551) 390-0362 to reach a roofer.
More questions? Call (551) 390-0362
Other services that may help
Chimney Flashing Repair
Chimney flashing rebuilt so the roof-to-brick joint sheds water again, so the ceiling beside the fireplace stays dry.
Learn moreRoof Leak Repair
Finding where water gets through the roof and sealing it at the source, so the stain on the ceiling stops growing.
Learn moreSkylight Repair
Skylight repair from the flashing on the roof to the glass and the frame, after sorting out whether the water is a leak or condensation.
Learn moreRoof Vent Repair
Repairing cracked pipe boots, broken box vents, loose ridge vents, seized turbines and exhaust hoods, so every opening in the roof stays sealed.
Learn more
Looking for something else?
See all roofing servicesNeed flashing repair in Montvale, NJ?
Call (551) 390-0362 for a local roofer in Montvale and nearby towns.